[WT-support] TI5/CT1ILT Help with K3+Win-test

[Zrinko Zibert]

You still have a problem with CW, its readable, just time to time some
letters are not with the same speed :)
TNX 12m CW QSO, GL in the contest

Zik DK8ZZ


2014-02-14 16:46 GMT+01:00 Filipe Lopes <ct1ilt at gmail.com>:

> Hello Rich
>
> thanks very much for the reply, by TX DLY you mean the VOX delay? just on
> the speed knob?
>
> I am not used to the K3 as I am a TS590 user.
>
> thanks again
>
> 73's Filipe Lopes
> CT1ILT, F4VPX, CR6K
>
>
>
> 2014-02-14 16:40 GMT+01:00 Rich - K1HTV <k1htv at comcast.net>:
>
>> Felipe,
>>  Greetings from snowy Amissville, VA. I just got inside after snow
>> blowing 19 inches of snow from our long driveway to the street and checked
>> my email to see your forwarded note from Frank, W3LPL.
>>
>> The problem of chopped characters that we had with my K3 was corrected by
>> reducing the "TX DLY" parameter from the default 30 to a lower setting of
>> 10.  I you are using an amplifier with your K3, try using the highest
>> number possible before the chopping occurs.
>>
>> 73,
>> Rich - K1HTV
>>
>> = = =
>>
>>
>> ----- Original Message -----
>> From: donovanf at starpower.net
>> To: support at win-test.com
>> Cc: "PVRC Reflector" <pvrc at mailman.qth.net>
>> Sent: Friday, February 14, 2014 10:10:30 AM
>> Subject: Re: [WT-support] TI5/CT1ILT Help with K3+Win-test
>>
>>
>> Hi Felipe,
>>
>> I had this exact same problem with K1HTV's K3.
>>
>> He changed a K3 parameter to fix it, but I don't remember which one!
>> The problem is documented on the Elecraft site, I'm sure you will find it.
>> It may also be corrected in a more current K3 firmware update.
>>
>> I suspect it was one of the timing parameters.
>>
>> 73
>> Frank
>> W3LPL
>>
>> ----- Original Message -----
>>
>> From: "Armin Sturm" <dk9py at t-online.de>
>> To: support at win-test.com
>> Sent: Friday, February 14, 2014 10:35:59 AM
>>
>> Subject: Re: [WT-support] TI5/CT1ILT Help with K3+Win-test
>>
>> Try to enter nosound in the Call Field to switch off pc speaker.
>> 73 Armin, DK9PY
>>
>>
>> Filipe Lopes <ct1ilt at gmail.com> schrieb:
>>
>>
>>
>> Hi guys,
>>
>>
>> I am in Costa Rica and I am using a K3 with win-test and my notebook with
>> WIN7 and when I increase speed over 34 36 WPM the CW starts to get messy,
>> some of the caracheters I send are almost unreadable, like C is almost Y.
>>
>>
>> I changed Keyer, was using K1EL Winkey, then I tried CW via CAT cable,
>> and then I have my own cable with a transistor and resistor and they all do
>> the same.
>>
>>
>> I tried unpluging the CAT system while txing with my cable keyer and
>> still the same.
>>
>>
>> I am using all USB TO RS232 converters that work well with my TS590.
>>
>>
>> I have changed into CW QRQ in K3 menu.
>>
>>
>> is there anything else I should look at?
>>
>>
>> thanks a million for help
>>
>>
>> 73's Filipe Lopes
>>
>> TI5W in ARRL CW
>>
>>
>>
>>
>>
>> CT1ILT, F4VPX, CR6K
>>  
>>
>>
>> _______________________________________________
>> Support mailing list
>> support at win-test.com
>> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>>
>>
>
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>


-- 
73s, Zrinko Zibert (Zik) DK8ZZ, VE3ZIK, YT3ZZ
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.f5mzn.org/pipermail/support/attachments/20140214/0fa62410/attachment.html>