[WT-support] TI5/CT1ILT Help with K3+Win-test

[Filipe Lopes]

Hello Rich

thanks very much for the reply, by TX DLY you mean the VOX delay? just on
the speed knob?

I am not used to the K3 as I am a TS590 user.

thanks again

73's Filipe Lopes
CT1ILT, F4VPX, CR6K



2014-02-14 16:40 GMT+01:00 Rich - K1HTV <k1htv at comcast.net>:

> Felipe,
>  Greetings from snowy Amissville, VA. I just got inside after snow blowing
> 19 inches of snow from our long driveway to the street and checked my email
> to see your forwarded note from Frank, W3LPL.
>
> The problem of chopped characters that we had with my K3 was corrected by
> reducing the "TX DLY" parameter from the default 30 to a lower setting of
> 10.  I you are using an amplifier with your K3, try using the highest
> number possible before the chopping occurs.
>
> 73,
> Rich - K1HTV
>
> = = =
>
> ----- Original Message -----
> From: donovanf at starpower.net
> To: support at win-test.com
> Cc: "PVRC Reflector" <pvrc at mailman.qth.net>
> Sent: Friday, February 14, 2014 10:10:30 AM
> Subject: Re: [WT-support] TI5/CT1ILT Help with K3+Win-test
>
>
> Hi Felipe,
>
> I had this exact same problem with K1HTV's K3.
>
> He changed a K3 parameter to fix it, but I don't remember which one!
> The problem is documented on the Elecraft site, I'm sure you will find it.
> It may also be corrected in a more current K3 firmware update.
>
> I suspect it was one of the timing parameters.
>
> 73
> Frank
> W3LPL
>
> ----- Original Message -----
>
> From: "Armin Sturm" <dk9py at t-online.de>
> To: support at win-test.com
> Sent: Friday, February 14, 2014 10:35:59 AM
> Subject: Re: [WT-support] TI5/CT1ILT Help with K3+Win-test
>
> Try to enter nosound in the Call Field to switch off pc speaker.
> 73 Armin, DK9PY
>
>
> Filipe Lopes <ct1ilt at gmail.com> schrieb:
>
>
>
> Hi guys,
>
>
> I am in Costa Rica and I am using a K3 with win-test and my notebook with
> WIN7 and when I increase speed over 34 36 WPM the CW starts to get messy,
> some of the caracheters I send are almost unreadable, like C is almost Y.
>
>
> I changed Keyer, was using K1EL Winkey, then I tried CW via CAT cable, and
> then I have my own cable with a transistor and resistor and they all do the
> same.
>
>
> I tried unpluging the CAT system while txing with my cable keyer and still
> the same.
>
>
> I am using all USB TO RS232 converters that work well with my TS590.
>
>
> I have changed into CW QRQ in K3 menu.
>
>
> is there anything else I should look at?
>
>
> thanks a million for help
>
>
> 73's Filipe Lopes
>
> TI5W in ARRL CW
>
>
>
>
>
> CT1ILT, F4VPX, CR6K
> ​ ​
>
>
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.f5mzn.org/pipermail/support/attachments/20140214/1262afad/attachment-0001.html>