[WT-support] WT and Winkey

[G3SJJ]

Thanks Kenth.

Your suggestion number 1 appears to have stabilised it for now. There is 
still a difference between speeds when I transfer from Logger32 to 
Wintest.  30wpm in Logger translates to 44wpm in Wintest. Well out the 
range for most contests. I have also found that if I leave a small delay 
between sending on the paddle and hitting an F Key, the problem of F Key 
not transmitting is avoided. Obviously a question of a timing issue in 
WT that I have not found before in K8CC's NA, Writelog or N1MM.

I always take out the + and - in the message. These should not be 
default as they are unnecessary for 99.999% of contest operating and are 
poor operating anyway.

Transmitting of the character ' is still present when using Alt F9/F10 
to make an increase in speed.

Not sure if the development team have seen my recent posting as yet 
again there has been no acknowledgment! What happened to good old 
courtesy, eh?

Chris G3SJJ



Kenth Johansson wrote:
> Chris,
> I don´t think I have the full soloution for the winkey problems together with the microkeyer but I have changed the following in my setup:
>
> 1. Options > Interfaces coniguration >Winkey > Configure. The default value for DTR, RTS pins are -Handshake-. I have changed to -Always on-.
>
> 2. F-messages. I don´t use + - values to change speed in a message.
>
> Theese changes have helped me.
>
> Kenth
> sm6dyk
>
> ----- Original Message ----- 
> From: "G3SJJ" <g3sjj at btinternet.com>
> To: <support at win-test.com>
> Sent: Wednesday, February 07, 2007 5:37 PM
> Subject: [WT-support] WT and Winkey
>
>
>   
>> Is there any progress on making WT work correctly with Winkey yet?
>>
>> I was operating in the FOC Marathon last weeeknd and had really bad 
>> problems. It is still very unstable. At one stage I had closed the 
>> computer down during a rest period. On rebooting at 0600, it took me 30 
>> minutes to get to a stable situation, consequently I missed some 
>> importna pre-sunrise DX QSOs. At first, keying from the paddles 
>> connected to mHam Keyer was normal, but when I pressed an F key, CW was 
>> sent to the PC loudspeaker instead of keying the radio, re-booting and 
>> reopening WT produced the same situation. Eventually I got to stage when 
>> WT was keying the radio correctly, but the speed variation between 
>> internal CW and via mH Keyer was again apparent. It is not good 
>> operating practice to transmit the character  '  when changing speed up 
>> or down using Alt F9/10. Also at times to would just send the first 
>> character of the F key message. eg F instead of FOC G3SJJ G3SJJ FOC.
>>
>> I am now setting up for RSGB 1.8MHz Contest, and again the  '  character 
>> is transmitted at Alt F9/10. In independent speed both speeds are 
>> currently set to 30wpm. The computer speed is correct whilst paddle sent 
>> speed is much slower. Adjusting the speed knob so that the speeds are 
>> the same shows 30 and 34.
>>
>> Earlier in this test session if I sent on the paddle and then hit an F 
>> Key nothing happened, as I reported after CQWW. Now, if I send a paddle 
>> message then hit an F key the first character is dropped. EG (Paddle) 
>> Pete    (Computer)  NN  instead of 5NN, or Est instead of Test. This 
>> only appears to happen when there is nothing in the callsign field.
>>
>> I am now at the stage when using WT is more of a liability than an asset 
>> and each time I run the program I ask myself what new features I will find!!
>>
>>
>> 73 Chris G3SJJ
>> _______________________________________________
>> Support mailing list
>> Support at win-test.com
>> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>>
>>     
>
> --------------------------------------------------------------------------------
> Jag använder en gratisversion av SPAMfighter för privata användare.
> 959 spam har blivit blockerade hittills.
> Betalande användare har inte detta meddelande i sin e-post.
> Hämta gratis SPAMfighter idag!
>
> _______________________________________________
> Support mailing list
> Support at win-test.com
> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>