[WT-support] K3NG Keyer

[Franck]

Hi Maciek & All,
This fixed my problem Winkey is now detected. 

Thanks & 73 de Franck, F4CIB

----- Mail original -----
De: "Maciek SQ6MS" <sq6ms at o2.pl>
À: support at win-test.com
Envoyé: Mardi 26 Janvier 2021 18:34:46
Objet: Re: [WT-support] K3NG Keyer

Hi

For Win-Key emulation If you are using Arduino Nano or other board 
(regardless if it`s original or clone) put 10 to 47uF electrolytic 
capacitor between RESET and GND pins.

For regular use this capacitor should always be connected. Disconnect it 
if you want to program (uploading new sketch) the board.

Hope this will help. Good Luck !

-- 
Vy73`s de Maciek SQ6MS/F4VSQ

W dniu 25/01/2021 o 19:30, Franck pisze:
> Hi All,
> struggling with my K3NG keyer and Win-Test.
>
> I compile K3NG keyer with last up to date firmware (2021-01-24)
> Keyer options used:
> #define FEATURE_COMMAND_LINE_INTERFACE  // Command Line Interface functionality
> #define FEATURE_WINKEY_EMULATION    // disabling Automatic Software Reset is highly recommended (see documentation)
> #define OPTION_PRIMARY_SERIAL_PORT_DEFAULT_WINKEY_EMULATION  // Use when activating both FEATURE_WINKEY_EMULATION and FEATURE_COMMAND_LINE_INTERFACE
> #define OPTION_INCLUDE_PTT_TAIL_FOR_MANUAL_SENDING
> #define OPTION_EXCLUDE_PTT_HANG_TIME_FOR_MANUAL_SENDING
> #define OPTION_WINKEY_STRICT_HOST_OPEN               // require an admin host open Winkey command before doing any other commands
> #define OPTION_WINKEY_2_SUPPORT                      // comment out to revert to Winkey version 1 emulation
> #define OPTION_WINKEY_INTERRUPTS_MEMORY_REPEAT
> #define OPTION_WINKEY_2_HOST_CLOSE_NO_SERIAL_PORT_RESET  // (Required for Win-Test to function)
> #define OPTION_WINKEY_IGNORE_LOWERCASE               // Enable for typical K1EL Winkeyer behavior (use for SkookumLogger version 1.10.14 and prior to workaround "r" bug)
> #define OPTION_PROG_MEM_TRIM_TRAILING_SPACES         // trim trailing spaces from memory when programming in command mode
> #define OPTION_DIT_PADDLE_NO_SEND_ON_MEM_RPT         // this makes dit paddle memory interruption a little smoother
> #define OPTION_CW_KEYBOARD_CAPSLOCK_BEEP
> #define OPTION_DO_NOT_SEND_UNKNOWN_CHAR_QUESTION
> #define OPTION_EXCLUDE_EXTENDED_CLI_COMMANDS
> #define OPTION_DISPLAY_MEMORY_CONTENTS_COMMAND_MODE
>
> On Win-Test side, Keyer connected to COM10 set to Winkey 8N2 DTR set always to 1, RTS always to 0 (tried as well default which are handshake for both)
> Options, Winkey configuration unchanged (i tried also winkey v2 features enabled):
> All unticked but paddle watchdog, Iambic A, PTT, 752Hz, tail&lead 50ms, fixed tail, synchronized by WT only
>
> And i got Winkey Device init Error on the status area
>
> Can anyone share with me his settings ?
>
> 73 de Franck, F4CIB
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support


-- 
Cet email a fait l'objet d'une analyse antivirus par AVG.
http://www.avg.com

_______________________________________________
Support mailing list
support at win-test.com
http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support