[WT-support] SO2R scenario $TR does not work

[Daniel "Danny" Horvat, E73M]

Bob, thanks a lot. You are right, it is default "Multiplier" scenario 
with $TR variable in secondary radio column.

I figure it out, each time I switch radios with [*] key I make that 
radio "Primary" and always execute only Primary radio column variables. 
I deleted all variables in secondary column since I do not need them.

It is much better scenario then what I used before.
With $TR2 variable I do not waste any time, after sending my call to 
needed multiplier on second radio, $TR2 $F1 command sends CQ on my run 
frequency while listening for answer from multiplier. If called Mult 
does not reply I switch back to RUN station for possible answers to my 
previous CQ.

Same applies when sending F2 message to new multiplier.

As CT1BOH says:"If you not CQing...you lose"

Once again, Bob thanks for your patience and great help to all of us.

73 CU all in CW leg...

Danny, E73M


---
Daniel Danny Horvat, E73M
Antennas by E73M
http://www.MyAntennas.com

On 2013-11-07 18:00, Bob Wilson, N6TV wrote:
> On Thu, Nov 7, 2013 at 3:19 PM, Daniel "Danny" Horvat, E73M
> <e73m at e73m.com> wrote:
> 
>>  Try this, choose scenario "check band", then press * to switch focus 
>> to secondary radio, then press F2 to send 599+zone.
>> It does send it but according variables in secondary radio column: 
>> $RESET $F2 $R1R1 $TR2 $MSG1, it should after 599+zone send the MSG1 (I 
>> set it to TEST E73M)on primary radio. Problem is that that $TR2 and 
>> $MSG1 does not execute at all.
> 
> First, did you mean "Press CAPS LOCK to switch focus to Secondary
> Radio"?  The [*] key swaps primary and secondary, it doesn't change
> focus to secondary.
> 
> The default "Check band" scenario doesn't have any $TR commands in
> the Secondary Radio column.  So when the secondary radio has the focus
> (yellow background), nothing will be sent on the primary radio.
> 
> Try changing it to:
> 
> $RESET $R1R1 $F1 $R1R2 $TR2 $MSG1
> 
>  There is great confusion because $TR2 doesn't mean "transmit on
> secondary radio".  It means "Transmit on OTHER (inactive) radio" (the
> one without the focus).  There is great confusion also because Radio 1
> can be either the Primary OR the Secondary radio, then you can swap
> them.
> 
> Try the following (copied from SO2R_Advanced.ini in /cfg directory):
> 
> [CW Scenario 3]
> Name=Check Band 
> Primary F1=$RESET $R2R2 $F1 $R1R2 $TR2 $MSG1
> 
> Primary F2=$R2R2 $F2 $R1R2 $TR2 $MSG1
>  Primary F3=$R2R2 $F3 $R1R2
> Primary F4=$R2R2 $F4 $R1R2
> Primary F5=$R2R2 $F5 $R1R2
> Primary F6=$R2R2 $F6 $R1R2
>  Primary F7=$R2R2 $F7 $R1R2
> Primary Insert=$R2R2 $INSERT $R1R2
> Primary Plus=$RESET $R2R2 $PLUS $R1R2 $TR2 $MSG1
> Secondary F1=$RESET $R1R1 $F1 $R1R2 $TR2 $MSG1
> Secondary F2=$R1R1 $F2 $R1R2 $TR2 $MSG1
> Secondary F3=$R1R1 $F3 $R1R2
> Secondary F4=$R1R1 $F4 $R1R2
> Secondary F5=$R1R1 $F5 $R1R2
> Secondary F6=$R1R1 $F6 $R1R2
> Secondary F7=$R1R1 $F7 $R1R2
> Secondary Insert=$R1R1 $INSERT $R1R2
> Secondary Plus=$RESET $R1R1 $PLUS $R1R2 $TR2 $MSG1
> 
> 73,
> 
> Bob, N6TV
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support