[WT-support] Winkey problem

[IZ7AUH Frank]

Hi bob,

I did not know this possibility as a flex5000 radio 1 and Radio 2 as a ic7400 which is connected microHAM mkII you advise me to use the WinKey flex5000 but I'm not sure I can do it

Francesco GIACOIA
Inviato da iPad 2

Il giorno 29/mag/2011, alle ore 12:04, "Bob Wilson, N6TV" <n6tv at arrl.net> ha scritto:

> On Sun, May 29, 2011 at 2:50 AM, Frank, IZ7AUH/AK1CQ <iz7auh at gmail.com> wrote:
> I try to setup with your suggests, but WinKey work on each Radio, 1 and 2, a WinKey configuration override a CW setup on Radio 1, if I desable WinKey on Setuo Iterface, CW setuo work fine on Radio 1.
> Any solution?
>  
> Yes, use one virtual COM port DTR line for CW keying on Radio 1, and a second virtual COM port DTR line for CW keying on Radio 2.
> 
> Or you can use the Winkey for both radios like most people do:  WKSETUP [Enter], Second output (Pin 5) = Radio 2.  Press OK.
> 
> Why do you only want to use the Winkey on one radio?  Is it because you want a different CW speed on each radio?  Win-Test does not support that.
> 
> 73,
> Bob, N6TV
> Da: "Bob Wilson, N6TV" <n6tv at arrl.net>
> Risposta: <support at win-test.com>
> Data: Thu, 26 May 2011 09:17:51 -0700
> A: <support at win-test.com>
> Oggetto: Re: [WT-support] Winkey problem
> 
> On Thu, May 26, 2011 at 6:15 AM, Frank, IZ7AUH <iz7auh at gmail.com> wrote:
> Hi,
> 
> I setup a Winkey of my Microham MKII on radio2, My problem is that I would like the Winkey is enabled only on radio 2 and no on both, how should I set?
> 
>  
> 
> 73 IZ7AUH
> 
> 
> I do not believe there is any way to tell Win-Test use the WinKey only for Radio 2, and some other message keying device for Radio 1.
> 
> Try this.  In the Winkey Configuration dialog  you can tell the WinKey to use its second output (Pin 5) for Radio 2 -or- for PTT.  If you set that to PTT, perhaps the WinKey will only work on Radio 1.  Then you can swap Radio 1 with Radio 2, and try using COM port CW keying for "Radio 1 only" on the serial port configuration dialog (select type = Other device, DTR=CW, Active With = Radio 2).
> 
> If that doesn't work, I recommend using one or two virtual COM ports, or the LPT port for on/off CW keying instead of using the Winkey.
> 
> FYI, I just expanded the documentation of the serial port configuration dialog in the online Wiki, since many people didn't seem to understand how to use the settings.  The virtual serial port pins can be used for CW on/off keying and PTT, or for high speed SO2R active radio control of a microHAM, EZMaster (?) or DXDoubler box via "Classic Auto Control" (set device type to Other interface).
> 
> 73,
> Bob, N6TV
> _______________________________________________ Support mailing list Support at f5mzn.org http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
> 
> _______________________________________________
> Support mailing list
> Support at f5mzn.org
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
> 
> 
> _______________________________________________
> Support mailing list
> Support at f5mzn.org
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.f5mzn.org/pipermail/support/attachments/20110529/3b13522f/attachment-0001.html>