[WT-support] problem comunication WT via micoHAM USB III -IC7700

[Bob Wilson, N6TV]

Chris is correct.  The default hex address for an IC756PRO-III is 6Eh,
according to this handy
reference<http://www.docksideradio.com/Icom%20Radio%20Hex%20Addresses.htm>.
50h is the address of a "standard" (non-Pro) IC-756.

Perhaps if ES5RY just changes the radio type in Win-Test from IC-765PRO-III
to IC-756, it will start to work fine.

If you are using two identical Icom rigs, assign one a non-standard address
using the radio's menu.  Then select radio type "Icom Generic" and edit the
WT.INI file, as explained here:

http://docs.win-test.com/wiki/WT.INI#Generic_ICOM_radio

Changing the Icom radio type so that it matches the non-standard address may
also work.

73,
Bob, N6TV

On Tue, Oct 26, 2010 at 2:24 AM, 9A5K <9a5k at 9a5k.com> wrote:

>  Tonno,
>
> default address for PRO III is 6E, if I remember it OK.
>
> However, he can check that in OTHER menu on TRX, where other communication
> parameters are show (CI-V, baud rate etc.)..
> Check the rate in TRX too..
>
> 73,
> Chris - 9A5K
>
> ----- Original Message -----
> *From:* Tõnno Vähk <Tonno.Vahk at gafm.ee>
> *To:* support at win-test.com
> *Sent:* Tuesday, October 26, 2010 11:21 AM
> *Subject:* Re: [WT-support] problem comunication WT via micoHAM USB III
> -IC7700
>
>  Actually ES5RY was having problem to get IC756 PROIII CAT to work. USB
> Router shows frequency and everything is fine but Win-Test does not read
> CAT.
>
>
>
> He used MK2R+ and settings:
>
>
>
> 19200, 8, N, 1. Address 50h. No settings in WT worked (CI-V on/off,
> handshake, always on/off, tried 4800 rate in the rig and USB router…)
>
>
>
> Any idea why WT might not read CAT while all fine in USB router? (same port
> of course and USB router says port opened)
>
>
>
> Can it be the problem of the address? Is 50h correct for PRO III?
>
>
>
> 73
>
> Es5tv
>
>
>
> *From:* support-bounces at win-test.com [mailto:support-bounces at win-test.com]
> *On Behalf Of *Bob Wilson, N6TV
> *Sent:* Tuesday, October 26, 2010 12:13 PM
> *To:* support at win-test.com
> *Subject:* Re: [WT-support] problem comunication WT via micoHAM USB III
> -IC7700
>
>
>
> On Mon, Oct 25, 2010 at 9:44 PM, sp7idx <sp7idx at interia.pl> wrote:
>
>  CI-V Baud Rate 19200
> CI-V Address 7Ah   <<<<<<<<<<<<<
> CI-V Transceive ON
> Decode Baud Rate 19200
>
>
>
> After several private messages back and forth, I finally noticed that this
> not the default CI-V  address for an IC-7700.
>
>
>
> Waldi changed the CI-V address back the default, 74h, then Win-Test worked
> fine.
>
>
>
> 73,
>
> Bob, N6TV
>
> ------------------------------
>
> _______________________________________________
> Support mailing list
> Support at win-test.com
> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>
> _______________________________________________
> Support mailing list
> Support at win-test.com
> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.f5mzn.org/pipermail/support/attachments/20101026/820ed6b4/attachment-0001.htm