[WT-support] CW to SSB mode change problem

[Bob Wilson, N6TV]

Did you check the two "Mute the microphone" check boxes in the Interface
configuration (SETUP)
screen<http://docs.win-test.com/wiki/Menu:Options#Configure_interfaces...>?
If your mic. is plugged into your sound card, the last one should probably
be *unchecked*.

Also, Start, Control Panel, Sounds and Audio Devices, Audio tab

Sound playback section
Volume button, Microphone Slider, make sure to *uncheck* "Mute"

Sound recording section
Volume button, Microphone Slider, make sure to *check* "Select"

73,
Bob, N6TV

2008/10/10 Robert Pack, NX5M <nx5m at txcyber.com>

>  Upon testing the CTRL-F1/F2....same result.
> However, I did discover that when I change from CW back to SSB, no matter
> how I do it (CTRL-Fx or just do it on the radio), I still have no voice
> input when I speak into the mic....however, if I press a F-message key it
> transmits the recorded message.  After that, I have my vox audio back.
> Seems pretty strange.
>
> ----- Original Message -----
> *From:* Bob Wilson, N6TV <n6tv at arrl.net>
> *To:* support at win-test.com
> *Sent:* Friday, October 10, 2008 12:14 AM
> *Subject:* Re: [WT-support] CW to SSB mode change problem
>
> Are you using WT 3.22?  I tried both WT 3.21 and WT 3.22 for an IARU
> contest, but I could not replicate the problem.  Switching from CW to SSB
> with Ctrl-F1 worked fine.  The F1 message plays back as expected.
> Please send a screen shot of your SETUP menu (probably too big for the
> reflector, so just send it to me).
>
> 73,
> Bob, N6TV
>
> 2008/10/9 Robert Pack, NX5M <nx5m at txcyber.com>
>
>>  Setting up my first 3 stations and put them on the air for the first
>> time tonight I discovered a problem.
>> This happened on all 3 stations and Wintest was set up for a mixed-mode
>> contest (IARU) in this case.
>> Testing out ssb with a friend, we next went to cw.  Upon returning to ssb
>> I could not transmit on ssb.
>> I had to click OPTIONS>CONFIGURE INTERFACES>OK.
>> After doing that, ssb audio came back to life.
>>
>> It seems as if the "enable soundcard" is being turned off and has to be
>> turned back on again after changing from cw back to ssb although when I open
>> the config window it shows to be still turned on.
>>
>> I would think that this would have been discovered during a past IARU
>> contest in which someone was doing mixed mode.  Or perhaps this is just
>> something recent OR I have overlooked something.
>>
>> I have yet to find anything that will tell me why this is happening.
>>
>>
>>
>> 73,
>> Bob NX5M
>>
>> _______________________________________________
>> Support mailing list
>> Support at win-test.com
>> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>>
>>
>  ------------------------------
>
> _______________________________________________
> Support mailing list
> Support at win-test.com
> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>
> _______________________________________________
> Support mailing list
> Support at win-test.com
> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.f5mzn.org/pipermail/support/attachments/20081010/e7672682/attachment-0001.htm