[WT-support] Swap Radio problems

[SM6CNN]

Hello Jozef,
No, it is still the same. It is also the same if I use a physical COM 
port or if I use my microKEYER 2R+.
73
Andy SM6CNN

Jozef Urban, OM7ZZ wrote:
> Hi Andy,
> 
> Any change if you dissable Router queries for both radios?
> (Ports tab | Set)
> 
> 73 Jozef
> 
> 
> ----- Original Message ----- 
> From: "SM6CNN" <sm6cnn at telia.com>
> To: <support at win-test.com>
> Sent: Wednesday, 25 July, 2007 17:07
> Subject: Re: [WT-support] Swap Radio problems
> 
> 
>>
>> Olivier F5MZN wrote:
>>> Hi agn,
>>>
>>> Someone reported some days/weeks before a problem swaping two radios in 
>>> SO2R (by memory, a Yaesu and and Icom). Could you please come back?
>>>
>>> Thanks and 73,
>> Hello Olivier,
>> I reported this problem with Orion and MP in early June. Here is a copy:
>>
>> Interesting that it works for Dani with the same radio set up but with 
>> the EZ-master instead of my MicroKeyer.
>>
>> If I set up my Orion as Radio 1 as follows:
>> VFO A: TX
>> VFO A: RX
>> VFO B: SUB RX
>> VFO A: 7010
>> VFO B: 3505
>>
>> And the FT-1000MP as Radio 2 as follows:
>> VFO A: 14015
>> VFO B: 21015
>>
>> In the best case the following happens with the Orion after Ctrl-S:
>> 1. VFO A changes to SUB RX and VFO B changes to RX and TX
>> 2. sometimes the bandwith and mode is changed
>> 3. VFO A goes to 21015
>> 4. VFO B goes to 14015
>> 5. VFO A changes to RX and TX and VFO B to SUB RX
>>
>> In this case I got the right frequency SWAP but after a lot of switching 
>> in the Orion.
>>
>> In the above example I connected the Orion to a COM port on the main 
>> board of the PC not to a virtual COM port via the microKEYER.
>>
>> The SWAP command to the Orion as checked with PortMon is:
>> *KVBAB  why? it should not be changed from KVABA
>> ?RMF  why ask for filter bandwith?
>> *AF21015000 this is the wrong frequency (=VFO B of the MP)
>> *RMM2 why set mode?
>> *KVABA OK, but why was it changed to KVBAB?
>> ?RMF  why ask again for filter bandwith?
>> *AF14015000 OK, at last the correct frequency
>> *RMM2 why set mode again?
>> *RMM2 why set mode again?
>> *KVABA unnecessary, this is what it was alreeady
>> @RMF250 filter bandwith is returned
>> @RMF250 filter bandwith is returned
>>
>> I believe that all these commands are causing a timing problem and in my 
>> opinion only one command should be sent to the Orion i.e.
>> *AF(VFOA of secondary radio)
>>
>> Maybe the commands to the Elecraft are as many causing the erratic 
>> behaviour reported by Steve.
>>
>> 73
>> Andy SM6CNN
>> _______________________________________________
>> Support mailing list
>> Support at win-test.com
>> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
> _______________________________________________
> Support mailing list
> Support at win-test.com
> http://www.f5mzn.org/cgi-bin/mailman/listinfo/support
> 
>