[WT-support] MKII message problem

[Tonno Vahk]

Thanks Simon!!

That did it. New installation helped. Perfect.

73
tonno

-----Original Message-----
From: support-bounces at f5mzn.org [mailto:support-bounces at f5mzn.org] On Behalf
Of Simon Schelkshorn
Sent: Thursday, October 24, 2013 8:00 PM
To: support at win-test.com
Subject: Re: [WT-support] MKII message problem

Hi Tonno,

please have a look on the LINE LED on the front of the MKII. Does the LED
change from blinking to continuously on when level of recorded audio drops?
If yes, then MKII swiches from microphone input to line input!

I know that problem! In that case only working solution I know is:
- disconnect MKII from computer
- in USB router click on Device and delete the problematic MKII from the
list of devices
- reboot
- reconnect MKII and reconfigure from scratch :-(

Good luck!
Simon, DJ4MZ


Am 24.10.2013 18:49, schrieb Tonno Vahk:
> I record in Router. Even closed Win-Test to be clean. Voice message 
> limit is default 20s. Changed it, no difference.
>
> MicroHam Codec has not been designated to other devices.
>
> Another thing I noticed is that at the moment when the recording level 
> drops to zero, the OUT->IN arrow on Audio Switching tab goes from grey to
red.
>
> On Air recording or not on air makes no difference. When I record on 
> air then the audio remains high in tranceiver when it drops on sound card.
>
> I would think other have had this problem with SSB messages as well as 
> it is not only me who has had it here...
>
>   t
>
> -----Original Message-----
> From: support-bounces at f5mzn.org [mailto:support-bounces at f5mzn.org] On 
> Behalf Of Joe Subich, W4TV
> Sent: Thursday, October 24, 2013 7:26 PM
> To: support at f5mzn.org
> Subject: Re: [WT-support] MKII message problem
>
>
> Are you trying to record in Win-Test or in the microHAM DVK?
>
> microHAM DVK has a "voice message time limit" is its options:
> Router | Options | DVK.
>
> Also look for other programs that may be messing with the sound card 
> ("headset mic (microHAM CODEC)").  Anything that might mute the mic 
> can cause problems - of *maximum importance* is to be sure that 
> Windows has not designated any input or output of microHAM CODEC as 
> either the system "Default Device" or the "Default Communications Device".
>
> 73,
>
>      ... Joe, W4TV
>
>
> On 10/24/2013 11:46 AM, Tonno Vahk wrote:
>> Thank you guys for LAME tips! Works now!
>>
>> Another major issue with Microham MKII's. Several of them do not 
>> allow recording SSB messages for more than 2-3 seconds. After that 
>> the recording level drops to zero and only noise is recorded.
>>
>> I have tried all - changed firmware, usb ports, etc. It happens on 
>> several different units on different computers and op systems.
>>
>> I have had this before coming and going. Anybody has a cure??
>>
>> tonno
>>
>> _______________________________________________
>> Support mailing list
>> support at win-test.com
>> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>>
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>
_______________________________________________
Support mailing list
support at win-test.com
http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support