[WT-support] Audio routing problem with YCCC SO2R+

[Bob Henderson]

It is looking that way.  Verbose SO2R reports exchanges when the numeric *
key is pressed and we switch between left and right radios.  When any of
the function keys are pressed any associated voice keyer message is played
but there is no audio switching and nothing whatsoever reported on the
verbose SO2R screen so there appears to be no data traffic between WT and
the SO2R+ software.

Mark will have to work around this through use of permanent split audio
when SO2R.  It'll be painful but it seems like his only option at this
stage.

Thanks for your help.  I'll get back to this after the weekend.

73 Bob, 5B4AGN

On 26 October 2012 15:01, Dennis Egan <egan.dennis88 at gmail.com> wrote:

> Bob
>
> According to the manual, that greying out of the Latch means that the
> SO2R Box controller
> doesn't support that function.  If that's the case, its doubtful
> anything we do will get it to work for this weekend.
> It sounds like something that the WinTest authors and Paul will have
> to get together on.
>
> Dennis W1UE
>
> On Fri, Oct 26, 2012 at 10:41 AM, Dennis Egan <egan.dennis88 at gmail.com>
> wrote:
> > Bob
> >
> > Make sure software/firmware are current- software is 1.3, firmware is
> > 1.2.  Update if needed.  Rx switch should  bein center position.
> >
> > On the SO2R box software, check the "verbose so2r" box.  You should
> > now be able to see commands as they
> > are sent to the box.  You can make note of the commands.  You can also
> > send the commands that work- I imagine they should be the same.  Paul
> > K1XM can modify software/firmware if needed, but he's in 6Y right now
> > with limited computer access, so it won't happen before the contest,
> > if that is the issue.
> >
> > Try turning off "Tools | Data Entry | Enable Run/S&P switching"- that
> > should ungrey the Latch mode on the secondary window, and try it
> > again.
> >
> > UE
> >
> >
> >
> >
> > On Fri, Oct 26, 2012 at 10:16 AM, Bob Henderson <bob at 5b4agn.net> wrote:
> >> Thanks Dennis.
> >>
> >> With SO2R advanced mode set within WT the scenario buffers contain these
> >> macros.  Unfortunately the SO2R+ box doesn't seem to want to respond to
> >> them.
> >>
> >> Under scenario 1 the F1 box contains:
> >>
> >> $RESET $R2R2 $F1 $R1R2
> >>
> >> F2 box contains:
> >>
> >> $R2R2 $F2 $R1R2
> >>
> >> Pressing F1 plays the F1 DVR message but apparently ignores the R2R2 and
> >> R1R2 commands.
> >>
> >> Similarly pressing F2 plays the F2 DVR message but ignores the routing
> >> commands.
> >>
> >> Might I have an SO2R+ hardware issue?
> >>
> >> 73 Bob
> >>
> >>
> >> On 26 October 2012 13:49, Dennis Egan <egan.dennis88 at gmail.com> wrote:
> >>>
> >>> Bob
> >>>
> >>> 2nd option- In some of the Wintest documentation, they actually showed
> >>> how to use macros
> >>> to emulate a LATCH situation- I ifted this from that.
> >>> Setting up scenarios
> >>>
> >>> A standard F1 message contains only the content of what is sent, i.e.
> >>> F1 = TEST CT3NT. When using Advanced SO2R mode the F1 message will
> >>> have the content plus the scenario to control audio and transmitting.
> >>> Imagine the following scenario:
> >>> F1 = $R2R2 $F1 $R1R2
> >>> This simple scenario will do the following. When the operator pushes
> >>> the F1 key, Win-Test will switch the headphones to radio2 only
> >>> ($R2R2), transmit the content of standard F1 message (TEST CT3NT) and
> >>> when that is over will switch the headphones to left ear on radio1 and
> >>> right ear on radio2 ($R1R2).
> >>> $R2R2 $F1 set up the audio headphone settings and transmission in
> >>> moment 1 of the QSO
> >>> $R1R2 sets the audio headphone settings for moment 2 of the QSO
> >>>
> >>> I realize it may not be exactly what you are looking for, but it might
> >>> work for you.
> >>>
> >>> GL
> >>>
> >>> UE
> >>>
> >>> On Fri, Oct 26, 2012 at 9:41 AM, Bob Henderson <bob at 5b4agn.net> wrote:
> >>> > Dennis
> >>> >
> >>> > Many thanks but checking the LATCH box in the SO2R program makes no
> >>> > difference to audio routing.  LATCH box in the WT Secondary Radio
> window
> >>> > is
> >>> > permanently greyed out.  I don't know whether that's significant.
> >>> >
> >>> >
> >>> > 73 Bob, 5B4AGN
> >>> >
> >>> >
> >>> > Bob
> >>> >
> >>> > In the SO2R Box program, there is a box called "LATCH".  Check that
> >>> > and you should get the
> >>> > functionality you seek.
> >>> >
> >>> > Dennis W1UE
> >>> >
> >>> >
> >>> > _______________________________________________
> >>> > Support mailing list
> >>> > support at win-test.com
> >>> > http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
> >>> >
> >>> _______________________________________________
> >>> Support mailing list
> >>> support at win-test.com
> >>> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
> >>>
> >>
> >>
> >> _______________________________________________
> >> Support mailing list
> >> support at win-test.com
> >> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
> >>
> _______________________________________________
> Support mailing list
> support at win-test.com
> http://lists.f5mzn.org/cgi-bin/mailman/listinfo/support
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.f5mzn.org/pipermail/support/attachments/20121026/28e7c1e9/attachment.html>